SUPPORTKnowledge BaseTraining Academy · Submit a Ticket · Warranty

Help Center

Search results

Showing matches for “RF tube”. Refine your search or browse below.

Popular:RF tube focus LightBurn rotary setup cut settings

40 results

Matches for “RF tube”

How to Clean RF Tube Air Filters on a Thunder Laser Bolt and Odin Series machinesBolt · Maintenance — Step-by-step guide for cleaning the RF tube air filters on Thunder Laser Bolt and Odin series machines to maintain proper air cooling.RF Tube- Change from Pre-Ignition to no pre-ignitionAll machines · General — ⚠ STOP — READ BEFORE PROCEEDING This procedure changes protected vendor-level laser settings, and the optional tuning in Part 2 can cause the tube to emit while the machine is idle. An external pre-ignition value that is set too high will make the ...RF Tube Shutter Bypass ProcedureAll machines · General — Step-by-step guide to temporarily removing the laser shutter on Class I Bolt and Titan series machines for diagnostic testing, including safety notices and restore instructions.How to adjust the 48V 30W RF Tube Power Supply Voltage for a Thunder Laser BoltBolt · Maintenance — How to measure and adjust the 48V DC power supply output voltage on a Thunder Laser Bolt with a 30W RF tube.How to Test the RF Tube and Fan BoardAll machines · General — Step-by-step guide to testing RF tube and fan board signal using a multimeter and jumper wire, including door interlock bypass.Iradion RF Tube and Fan Control Board: Ports, Wiring, and LED IndicatorsAll machines · General — Reference guide for Iradion RF tube signal wiring, LED status indicators, and fan board lights on Thunder series machines with v2.7+ fanboards.SPT RF Tube and Fan Control Board Ports and LED Indicators for TroubleshootingAll machines · General — High-level technical reference for SPT RF Tube Fan Control Board port designations, LED indicators, wiring connections, and signal testing procedures for troubleshooting.Bolt Series RF Tube Beam Expander TuningBolt · Maintenance — How to tune the beam expander on a Bolt Series laser machine, including a video explanation and downloadable test file.Can I Upgrade My Glass Tube Nova/Mars/Mini to an RF Tube?Nova · General — Yes, the swap is possible, but Thunder Laser USA does not support it. Learn why and what's involved before you decide.Thunder Bolt RF Tube Manual for SPT ZAMIA 30W N30 series laser tubesBolt · General — Please see the attached RF Laser Tube Frequency ExplainedOdin · Materials & Parameters — Learn how RF laser tube frequency affects engraving and cutting quality, how to choose the right frequency for your material, and how to set it in LightBurn.How to convert your Laser machine to a higher Wattage Laser Tube between 80, 100 and 130 watts of Power - What all you will needAll machines · General — An overview of parts and reference material needed to convert a Thunder Laser Nova series machine to a higher wattage laser tube (80, 100, or 130W).Thunder Laser Nova Plus Zamia SPT ET-60 RF Laser Tube ManualNova Plus · General — Preface: Please see the attached manual for the 60W RF Tube in the Nova Plus machines How to make a cable and test Pulse an RF Laser Tube for ODIN and BOLTBolt · General — Step-by-step guide to building a test pulse cable for RF laser tubes in Odin and Bolt lasers, including wiring, connections, and safe test-fire procedure.How to Replace the 30W RF Laser Tube on Your Thunder Laser Bolt MachineBolt · Maintenance — Step-by-step instructions for removing and installing the 30W RF laser tube source on the Thunder Laser Bolt machine, not including alignment.Nova Plus Zamia SPT ET-80 RF Laser Tube ManualNova Plus · General — Reference manual for the 80W RF laser tube used in Thunder Laser Nova Plus machines.RF Excited CO2 Laser TubesAll machines · General — Overview of how RF excited, air-cooled metal CO2 laser tubes work in Thunder Laser Nova and Odin series machines, including striking voltage, tube degradation, and beam properties.The Difference Between DC and RF Excited CO2 Laser TubesAll machines · General — An overview of DC excited and RF excited CO2 laser tubes, covering how each works, their key differences, and which may suit your application.Titan: Iradion RF Laser Tube Manual and DatasheetTitan · General — Links to the Iradion RF laser tube manual and datasheet for Thunder Laser Titan series machines, with notes on part number conventions.Thunder Laser Nova PLUS RF Machine User ManualNova Plus · General — Please see the attached manual for the Thunder Laser Nova Plus Machines with RF tubes.Nova Plus Machine Hardware Identification Pictures and ImagesNova Plus · General — A visual reference guide identifying the hardware components and their locations on the Nova Plus laser machine, which uses an RF tube and no chiller.Odin Series DSP TL Timer Mid 2022 Block Diagram v8.4Odin · General — Please See the Attached: TL Timer V8.4 Flap V4.1 Page 1: Power Control - RF Tube Page 2: Controls signals Without RF Fan Control Page 3: Control Signals with RF Fan Control Page 4: Relay Control How To Replace The Nova Series DC TubesNova · Troubleshooting — Step-by-step guide for swapping the laser tube on Nova series machines, covering wire disconnection, tube removal, and new tube installation.55 Watt RF (Coherent) Material LibraryOdin · Materials & Parameters — Suggested laser settings (power, speed, interval, air assist) for common materials using a 55-watt RF (Coherent) laser tube.DC Excited CO2 Laser TubesAll machines · General — An overview of how DC excited, water-cooled glass CO2 laser tubes work, including tube construction, striking voltage, degradation, and power supply response.DC vs RF vs Fiber Deep Engrave Resolution On StoneAll machines · General — THIS DOCUMENT IS IN PROCESS. CHECK BACK OFTEN! This was my first time using the multi-cam 'live production' workflow with a remote so please excuse my excessive use of 'uh' as well as all of the other hiccups :) This test will be done on stone ...Thunder Laser Beam Spot Size based on Tube and Source Wattage All machines · General — This data is assuming all stock machines with proper optics/alignment/focus... etc...dot size will also increase with power output. Nova Series Nova Plus Bolt Titan Odin Aurora Nova Series The Nova series machines have DC excited watercooled glass ...Nova Laser Tube Will Not Fire or is Low on Power- LPSU TestNova · Troubleshooting — Learn how to perform the "Red Button Test" on Nova series laser machines to isolate and diagnose LPSU or laser tube power issues.Getting Controller Info From Within LightBurnAll machines · Software — Learn how to retrieve controller info (hours, firmware, job counts) from LightBurn V2.0+ and older versions, and how to interpret the data displayed.LoneStar Adhesive Material TestsAll machines · Getting Started — Learn how to perform material tests on LoneStar Adhesive materials using your Thunder Laser and LightBurn Material Test files.Nova Plus 60w Fan Power and Speed Control Wiring ChangeNova Plus · Maintenance — Step-by-step instructions for changing the cooling fan power and speed signal wires on the Nova Plus 60W from the Fan Control board to the laser tube.ODIN 22 Machine Pictures From 2022 Reference ImagesOdin · General — Reference images of internal components for a 2022 model ODIN 22 laser, covering sensors, electrical cabinets, tube door, and Z axis mechanical parts.Odin Series Beam Alignment ProcedureOdin · Maintenance — Preface: This article covers the basics of aligning the laser beam on your Odin RF Laser Tools Required: Flat Head screwdriver Allen Wrenches - 1 Roll of Masking Tape 1 safety goggles SAFETY INFO: C02 Laser Radiation, PPE, & Fire Suppression Warning ...Power Output Anomaly: Line (Vector) vs Engrave (Raster)All machines · General — Explains why DC excited CO2 laser tubes produce different power output between Fill (raster) and Line (vector) layers, with test data from a Nova 35-80w.Power Output Anomaly: Line (Vector) vs Engrave (Raster)All machines · General — Explains the power output anomaly between Fill (Raster) and Line (Vector) layers on DC excited CO2 laser tubes, with test data from a Nova 35-80w.Repacking & Moving Your ThunderAll machines · General — Best practices for repacking and moving Thunder Laser gantry-series machines, including securing the head, bed, blades, chiller, and laser tube.Thunder Laser Machine Preventative Maintenance Checklist - PM ChecklistAll machines · General — Preface: Proper care and routine maintenance of the machine will ensure optimal performance over a long service life. As you operate the machine, you need to build in time to your schedule for maintenance tasks. Also how you have the machine ...Bolt Plus and Bolt Pro 22 30w Coherent Tube Spec Sheet - Diamond C-30Bolt · General — Preface: This article has a spec sheet from the OEM. Your tube should be marked as a C30 model. Specs Overview: OEM website can be found here.Bolt Pro 32 and Odin 32 55w Coherent Tube Spec Sheet - Diamond C-55Bolt · General — Spec sheet for the Coherent Diamond C-55 (C55-A) CO2 laser tube used in the Bolt Pro 32 and Odin 32 55W machines.Dust Cover For 100w & 130w SPT TubesAll machines · General — Explains the optional dust prevention sleeve for Nova series machines with 100W and 130W SPT tubes, including how to install it and how to request one.